https://www.kairostech.com.tw/wp-content/uploads/2024/05/1.png
502
992
poweruser
https://www.kairostech.com.tw/wp-content/uploads/2022/01/KairosTech-1-1000x248.jpg
poweruser2024-05-24 11:04:192024-05-30 19:29:12Allegro 如何針對已走對線變更線寬與間距
https://www.kairostech.com.tw/wp-content/uploads/2022/11/1.jpg
455
715
poweruser
https://www.kairostech.com.tw/wp-content/uploads/2022/01/KairosTech-1-1000x248.jpg
poweruser2024-04-29 15:10:342024-05-30 19:30:22Allegro 如何快速將同類型的DRCs設為忽略狀態(Waived)
https://www.kairostech.com.tw/wp-content/uploads/2024/03/1.png
432
392
poweruser
https://www.kairostech.com.tw/wp-content/uploads/2022/01/KairosTech-1-1000x248.jpg
poweruser2024-03-20 11:18:282024-05-30 19:29:12Allegro 設定了 Signal Model 但沒有生成 Xnet 的解決方法
https://www.kairostech.com.tw/wp-content/uploads/2024/02/9.jpg
247
384
poweruser
https://www.kairostech.com.tw/wp-content/uploads/2022/01/KairosTech-1-1000x248.jpg
poweruser2024-02-07 11:09:262024-05-30 19:30:30如何利用DFM檢查找出通孔與盲孔重疊的問題
https://www.kairostech.com.tw/wp-content/uploads/2024/02/2.png
806
953
poweruser
https://www.kairostech.com.tw/wp-content/uploads/2022/01/KairosTech-1-1000x248.jpg
poweruser2024-02-07 10:59:182024-05-30 19:30:38OrCAD Allegro Cross Probing - 零件與滑鼠屬標自動連結
https://www.kairostech.com.tw/wp-content/uploads/2023/12/4.jpg
381
817
poweruser
https://www.kairostech.com.tw/wp-content/uploads/2022/01/KairosTech-1-1000x248.jpg
poweruser2023-12-11 01:51:412024-05-30 19:31:37如何變更已放置的Footprint
https://www.kairostech.com.tw/wp-content/uploads/2023/09/11.jpg
499
1255
poweruser
https://www.kairostech.com.tw/wp-content/uploads/2022/01/KairosTech-1-1000x248.jpg
poweruser2023-09-05 10:07:032024-05-30 19:29:12如何利用Impedance Workflow監測阻抗值
https://www.kairostech.com.tw/wp-content/uploads/2023/08/1-1.jpg
352
501
poweruser
https://www.kairostech.com.tw/wp-content/uploads/2022/01/KairosTech-1-1000x248.jpg
poweruser2023-08-29 10:22:172024-05-30 19:30:56如何輸出與讀入GDS檔案
https://www.kairostech.com.tw/wp-content/uploads/2023/08/4.jpg
369
640
poweruser
https://www.kairostech.com.tw/wp-content/uploads/2022/01/KairosTech-1-1000x248.jpg
poweruser2023-08-03 10:30:302024-05-30 19:29:12如何找出在輸出Gerber後所丟失的Pad
https://www.kairostech.com.tw/wp-content/uploads/2023/03/6-1.jpg
359
886
poweruser
https://www.kairostech.com.tw/wp-content/uploads/2022/01/KairosTech-1-1000x248.jpg
poweruser2023-03-13 03:31:262024-05-30 19:29:12如何一次刪除Xnet